News_Jiangyin Tengma Standard Parts and Tools Co., Ltd.

News

News Center

The rolling machine uses one rolling head to roll a variety of steel bars.

The thread rolling machine uses cutting and rolling thread to form at one time to achieve the purpose of reinforcing steel bar end and thread processing, which solves the problem of pretreatment of steel bar end before processing and the problem of multiple times of rolling for similar equipment, thus reducing process processing and multiple steel bar handling on site and improving the production and processing efficiency on site. The thread rolling machine can roll steel bars of various specifications by using one thread rolling head, it solves the situation that the same kind of equipment needs one thread rolling head for each specification to process straight thread of steel bar end. The rolling machine adopts internal cooling liquid, which solves the problem of chip removal during rolling processing. The automation strength is high, and the feed stops automatically and resets automatically. The straight thread rolling machine is a special equipment for processing the straight thread head of the steel bar. The end of the steel bar is rounded by stripping the ribs, and then the steel bar is rolled with three hollow thread rolling wheels to achieve the straight thread forming of the steel bar. Quality requirements.

2024

How to adjust the washboard for screw processing

Adjust the gap between the two washboard, and then tighten and fix it. Adjust the gap between the two plates so that the blank can be pressed tightly. If the gap is too large, the blank will not be rubbed and fall off.

2024

Adjustment method of thread roller

Unscrew the hexagon socket head cap of the thread roller shaft, remove the front bearing seat of the thread roller shaft to install the thread roller, and adjust the axial position of the thread roller with a spacer or fine adjustment.

2024

Common problems and treatment methods in the work of thread rolling machine

The front travel switch is broken (about 7000 times); The delay relay does not operate; The distance between the pressure block and the travel switch is not enough, the pressure block is not in place or the jam is damaged; The wiring falls off; Whether the contact is poor or damaged; Check whether the front limit contact is not in place, the closing point is open, the opening point is closed and the opening point of the time relay is closed; Check whether the limit and closing point at the back of the machine are open, check the point of the line, whether the line is loose, poor contact, damaged, broken, etc;

2024

Wire rolling machine processing should pay attention to what matters

During the production process, attention should be paid to adjusting the silk dental plate, paying attention to the installation position of the long and short dental plates and whether they are parallel to the height, and turning the flywheel by hand to check whether the feeding time is correct, which is suitable for mass production of fasteners and standard parts. The higher operating temperature of the wire rolling machine will reduce the hardness and strength, resulting in the early wear of the wire rolling machine material or plastic deformation and failure.

2024

Adjustment method of thread rolling plate clearance of thread rolling machine

The clearance of the washboard of the thread rolling machine refers to the distance between the upper and lower plates of the washboard, which will affect the thickness, uniformity and quality of the thread rolling. If the gap is too large, it will lead to uneven rolling, insufficient force, and unqualified finished products; if the gap is too small, it will lead to poor rolling and easy damage to the machine.

2024

Correct method of adjusting the washboard

The correct method of adjusting the washboard mainly includes adjusting the height, pressure and angle of the washboard, as well as the gap between the two washboards. These adjustment steps are essential to ensure the normal operation of the thread rolling machine and the quality of the thread rolling.

2024

Failure form of washboard

The most common failure forms of the washboard are: fatigue damage, abrasion, knife collapse, tooth stacking, tooth peeling, etc.

2024

< 1 2 >

Get a Free Consultancy

Tengma Standard Parts and Tools Co., Ltd.

Tengma tools specializing in the production of various specifications of the washboard, rolling wheel, and according to customer demand for a variety of standard customization.

+86-13771238158

185881693@qq.com

202 Zhencheng Road, Jiangyin City, Jiangsu Province

Quick links

Products
Solution
Tengma Overview
R&D

News
Contact Us

www.300.cn | Label

Business License